The right generator size depends on what you want to run during an outage, not on how big your house is. Homes with the same square footage often have very different power needs. To answer “What size generator do I need for my house?” start by listing the equipment you can’t go without when the power goes out.
Calculating required capacity depends on the equipment you run during an outage. A small home with an electric furnace and well pump can need more power than a large home with gas heat. Triangle Heating, Cooling, Plumbing, & Electrical provides electrical service across Central Pennsylvania. This guide explains how to choose generator size for your home, from estimating electrical loads to picking the right home standby generator.
What Size Whole House Generator Do I Need?
Determining generator capacity starts with choosing between essential circuit backup and whole-home coverage. Essential circuit coverage powers core emergency equipment. This setup typically runs a refrigerator, sump pump, heating controls, and select lighting circuits. Essential systems use a smaller generator. Whole-home backup powers every household circuit at once, so the whole-house generator size has to cover all your major loads running together. A load calculation determines the exact home generator size, as shown below.
Square footage alone does not determine power requirements. Electric heating and water heaters demand far more electricity than natural gas systems. For example, an electric water heater can draw 3,000 to 4,500 watts while it’s heating. Oversizing a standby generator wastes fuel. Undersizing causes voltage drops, trips circuit breakers, and damages electronics.
Homeowners can estimate basic power needs using DIY estimation methods. You can check UL nameplates on appliances or use a plug-in wattmeter to measure actual wattages. Online wattage calculators also help estimate general power draw. For exact sizing, technicians follow National Electrical Code (NEC) Article 220 calculation standards. A licensed electrician in Bellefonte, PA, can run a proper load calculation before installation.
- Essential coverage (7–11 kW): Runs refrigerators, sump pump units, internet routers, and lights.
- Partial home coverage (12–18 kW): Powers essential circuits plus a 3-ton central A/C system.
- Whole-home coverage (20–26 kW): Supports large homes with multiple A/C units, electric range, and heat pumps.
- Heating load factors: Gas furnaces need 600 watts, while electric heat strips require 10,000 to 15,000 watts.
These ranges provide a useful starting point, but every home has different electrical demands. The safest approach is to calculate the equipment you want to run during an outage and account for both running and startup wattage. A professional load calculation can confirm the right generator size and help prevent unnecessary oversizing, system overloads, or interruptions when you need backup power most.
Understanding Running Watts and Starting Watts
Accurately sizing a generator requires understanding running watts and starting watts. Running watts represent the continuous electricity an appliance uses while operating. Simple resistive loads like incandescent lights, televisions, and electric griddles only use running watts. Their power consumption stays constant while powered on.
Motor-driven equipment requires extra surge power to start electric motors. This temporary surge is known as starting watts. Electric motors in compressors and pumps draw three to four times their running power for two to three seconds upon startup. The National Electrical Code also requires a standby generator with an automatic transfer switch to be sized for the full load it serves, or to use a load management system that limits what runs at once.
- Central A/C (3-ton unit): Requires 3,500 running watts and 10,500 starting watts.
- Refrigerator or freezer: Uses 700 running watts and 2,200 starting watts.
- Well pump (1/2 HP): Demands 1,000 running watts and 2,800 starting watts.
- Sump pump (1/2 HP): Consumes 1,050 running watts and 2,150 starting watts.
- Microwave oven: Needs 1,000 running watts and zero additional starting surge.
Not accounting for starting surge can overload the system. When multiple motor loads start at once, an undersized home standby generator may trip its breaker or stall. Proper maintenance of cooling equipment reduces electrical strain on backup power. Scheduling routine air conditioning service in Bellefonte keeps compressor motors operating efficiently.
How Many Watts Does a House Need From a Generator?
Calculating the generator wattage your home may need starts with identifying which appliances and systems you want to operate during an outage. Add the running watts for equipment that may operate at the same time, then account for the highest starting or surge demand among motor-driven appliances. Because compressors, pumps, and blower motors can temporarily draw much more power when starting, include this extra demand when estimating generator capacity.
Common household equipment may include:
- Refrigerator or freezer: about 700 running watts, with startup demand that may exceed 2,000 watts
- 1/2 HP sump pump: about 1,050 running watts, with a higher temporary starting demand
- Central air conditioner: one of the larger household loads, with startup wattage that can be significantly higher than normal operating demand
- Gas furnace blower: typically requires continuous operating power plus additional wattage when the motor starts
- Electric water heater: may require several thousand watts while its heating elements are operating
- LED lighting circuits: generally use substantially less electricity than major HVAC, pumping, or water-heating equipment
Treat these figures as general examples only, because actual wattage varies by equipment size, model, efficiency, voltage, and manufacturer specifications. Appliance nameplates can provide a useful starting point, but homeowners planning a permanent standby system should have a professional evaluate the home’s actual electrical loads before selecting generator capacity.
A professional load assessment can account for the electrical panel, individual circuits, HVAC equipment, pumps, and other high-demand systems that may need backup power. A properly selected automatic transfer switch also allows the generator to supply designated household circuits while keeping the backup system isolated from utility power.
Homes with major mechanical equipment should include those loads in the generator-sizing process. If your property relies on a boiler, well, or plumbing equipment supported by Triangle’s plumbing services, or other essential systems, include their electrical requirements in the calculation. Professional generator installation can help ensure the selected system is appropriately sized and integrated with your home’s electrical system.
Choosing the Right Generator for Your Home
Selecting a home backup generator requires balancing essential appliance loads with peak motor-starting power. Square footage estimates alone cannot replace accurate electrical calculations. Combining DIY wattage tracking with professional load evaluations protects your sensitive equipment. An accurately sized generator powers your home smoothly, protects appliance motors, and maintains critical heating and cooling systems during unexpected power outages.
Schedule Professional Generator Sizing in Central Pennsylvania
Protect your property with a standby generator system tailored to your home’s exact electrical load. Triangle Heating, Cooling, Plumbing, & Electrical provides professional load calculations and generator installation across Bellefonte, State College, Centre County, and surrounding communities. Our experienced electricians evaluate panel capacity, install automatic transfer switches, and ensure full electrical code compliance. Contact Triangle Heating, Cooling, Plumbing, & Electrical today to schedule your home electrical evaluation.